Industry Insights & Guides

ANSI A10.11 vs OSHA vs EN 1263: Which Standard Applies?

A US buyer cites ANSI A10.11, a European one EN 1263, and OSHA is the law on US sites. They are three different kinds of document — and a pass under one is not a pass under another.

Construction workers in harnesses installing green safety netting on scaffolding at height
A buyer in the United States asks for a net to ANSI A10.11. A buyer in Europe asks for EN 1263. A site inspector in the United States cites OSHA 1926.502. All three are talking about safety nets, and all three are right — but they are not three names for the same thing. They are three different kinds of document: a law, a voluntary standard and a product standard. Knowing which one governs your job decides what test the net must pass, what paperwork must come with it and what happens if it does not comply.

The three documents, in one paragraph each

OSHA 29 CFR 1926.502(c) is the law on United States construction sites. It is a regulation, not a recommendation: where it applies, compliance is mandatory and enforceable. It sets performance and installation criteria for safety net systems — how far below the work the net may hang, how far it must reach past the edge, mesh size, border rope strength, the on-site drop test and inspection. It is not a full product specification; it tells you what the installed system must do, and leaves the net itself to be proven against it.
ANSI/ASSP A10.11 is a voluntary consensus standard for personnel nets. The current edition is A10.11-2010 (R2016), "Safety Requirements for Personnel Nets", and it sets minimum design, testing and use requirements for the selection, installation and use of personnel nets during construction, repair and demolition. Voluntary means no inspector can cite it on its own — but project specifications, contracts and buyers invoke it constantly, and once a spec names it, it becomes binding for that job. Note the scope: the reaffirmed 2016 edition covers personnel nets only; debris nets have their own standard, ANSI A10.37. A debris net is not a personnel net, and the two must never be substituted for each other.
EN 1263 is the European product-and-positioning pair. EN 1263-1 tests the net itself — mesh, border rope, energy absorption and the drop test — and sorts nets into classes A1/A2/B1/B2 and systems S, T, U and V. EN 1263-2 sets the positioning limits: fall height, catching width, anchorage loads and clearance below. Together they describe both the product and how it must be installed, which is why a European buyer will usually cite both parts.

Side by side: where they agree, and where they do not


OSHA 1926.502(c)
ANSI A10.11-2010 (R2016)
EN 1263-1 / -2
What it is
US federal regulation — the law on site
Voluntary US consensus standard
European product + positioning standards
Who it binds
Every employer on a US construction site where it applies
Whoever the contract or spec names
Whoever the project spec or local rules name
Mesh, maximum
36 sq in (230 cm²), no side longer than 6 in (15 cm)
36 sq in, no side longer than 6 in — the same ceiling as OSHA
100 mm for a system S net
Border rope, minimum
5,000 lb (22.2 kN) breaking strength
Set by the standard's own design requirements
30 kN (about 6,700 lb)
Drop test
400 lb (180 kg) sand bag, 30 ± 2 in diameter, dropped on site from the highest working surface, never from less than 42 in above it
Its own drop-test procedure, set by the standard
Type approval: 100 kg dropped from 7 m for a class A2 net
Positioning
No more than 30 ft (9.1 m) below the work; reach past the edge 8 ft / 10 ft / 13 ft as the drop grows
Selection, installation and use requirements
Maximum fall height 6 m (3 m within 2 m of the edge); anchorage 6 kN, spaced under 2.5 m
Inspection
At least once a week; drop test repeated after installation, relocation, major repair and every 6 months in one place
Inspection and use requirements in the standard
Removable test meshes checked annually for residual strength after UV exposure and ageing
Two things in that table matter most. First, the numbers are close but not identical, and close is not the same: an EN 1263 border rope at 30 kN is stronger than OSHA's 5,000 lb minimum, and a 100 mm EN mesh is smaller than OSHA's 6-inch ceiling — so a net built to EN 1263-1 will usually clear OSHA's mesh and border-rope figures. But that does not make it OSHA-compliant. OSHA still demands its own on-site drop test and its own positioning rules, and a European type-approval certificate is not a substitute for either. Second, the tests themselves are different shapes: EN 1263 drops 100 kg from 7 metres in type approval; OSHA drops 400 lb of sand on the actual jobsite, from the actual working surface. A pass under one is not a pass under the other.
There is also a historical link worth knowing. OSHA's drop test grew out of the early ANSI work: the 1977 edition of A10.11 recommended dropping a 400 lb bag of sand from 25 feet into the centre of the net with no broken strands or significant distortion. The modern OSHA test is done from the working surface instead, but the family resemblance is why the two are so often mentioned together — and why buyers sometimes assume they are interchangeable. They are not.

Which standard applies to your job?

Ask in this order:
  1. Where is the site? On a United States construction site, OSHA 1926.502 applies as law, whatever else is specified. In Europe, EN 1263 is the reference most specs will name, alongside local regulations that can be stricter.
  1. What does the project specification name? The spec is the document that decides the order. If it names ANSI A10.11, the net must meet A10.11; if it names EN 1263-1 and -2, it must meet both parts. If it names both, the stricter requirement governs wherever they differ — several jurisdictions, Quebec among them, say exactly that in their own regulations.
  1. Personnel or debris? A personnel net catches people; a debris net catches falling objects. They are built to different standards, tested differently and regulated differently. Under OSHA, using a debris net where a personnel net is required is a citable violation, even if the debris net looks similar. Under ANSI, debris nets belong to A10.37, not A10.11. The debris-vs-fall-arrest guide on this site explains the difference in full.
If no standard is named at all, that is itself a warning sign. A specification that just says "safety net" has not specified anything testable — ask which standard and edition the buyer is working to before quoting.

What to ask your supplier

Before ordering, ask these six questions and keep the answers with the net's label:
  1. Which standard and edition was this net tested to — ANSI A10.11, EN 1263-1, or both — and can I see the test report, not just a claim on a brochure?
  1. For a US job: does the net meet OSHA 1926.502(c) on mesh (36 sq in maximum), border rope (5,000 lb minimum) and panel connections, and will it pass the on-site 400 lb drop test?
  1. For a European job: what class and system is the net (for example A2, system S), and does it come with its EN 1263-2 instruction manual — anchorage forces, maximum fall height, catching width and clearance below?
  1. Is this a personnel net or a debris net — and if it is a debris net, is it being sold as one, not as fall protection?
  1. What are the removable test meshes for, and how often must they be tested for residual strength?
  1. Who inspects the installation before first use, and how often is it re-inspected — weekly, as OSHA requires, or to the schedule in the manual?
If a supplier can quote a standard but cannot show the test report that names it, the standard has been quoted, not met — and the difference only shows up when the net is tested, or when it is needed.