Industry Insights & Guides
How to Order a Custom Safety Net: Size, Mesh, Rope & Cost
A custom net is only as good as the measurements and specification behind it. Get the size, mesh, rope and test-mesh details right first — and the price you are quoted will actually mean something.

Almost no safety net is bought off the shelf. Scaffold bays are never the same width, openings are never square, and a container door is not a warehouse rack. So most safety nets are made to order — cut, edged and roped to the measurements a buyer sends in. That makes the order itself the most important part of the purchase: a net made to the wrong size, the wrong mesh or the wrong rope is not a bargain, it is a net that cannot be installed properly, and a net that cannot be installed properly cannot be trusted to catch anything.
This guide is about how to order one well. It covers what to measure, what to specify, and what drives the cost — so that the quote you receive is for the net you actually need, not for a generic net that happens to be near your size.
1. Start with the job, not the product
Before any measurement, decide what the net has to do, because that decides almost everything else:
- Fall-arrest or debris containment? A personnel net must absorb a falling body; a debris net must stop tools and rubble. The two jobs use different mesh sizes, different classes and different standards, and a net that does one well may be wrong for the other. The difference is explained in the site's debris-vs-personnel guide.
- Which system? Under EN 1263-1, System S is a horizontal net with a border rope, System T is attached to brackets, System U is a vertical net fixed to a supporting structure, and System V is a vertical net with a border rope attached to a gallows-type support. The system decides how the net is fixed and what its edges must carry.
- Which class? Class A nets are tested for a lower energy level than Class B nets; the label guide explains A1/A2/B1/B2. Do not order a class because it sounds stronger — order the class the job's fall height and standard require.
- Which standard applies? EN 1263 for most of Europe and many export markets, OSHA 1926.502 for the United States, ANSI A10.11 as the US product standard. The standards comparison guide sets out where each one applies. A supplier who cannot say which standard the net is made to has not really specified it.
Send the supplier the job description with the order — working height, fall height, what the net must catch, and the standard it must meet. A good supplier will ask for it if you do not send it; a supplier who never asks is a warning sign.
2. Sizes: measure the opening, then add what the net needs
The most common ordering mistake is measuring the net instead of the opening. Measure the space the net must cover, in place, and let the supplier work out the net size from that. What to send:
- Length and width of the opening, measured at several points — scaffold bays, building faces and container doors are rarely as square as the drawing says. Send the largest measurement for each side, and say so.
- The fixing points. Where will the net actually be tied or clipped? The distance between fixing points matters more than the overall opening, because the net must reach them with enough slack to sag and absorb a fall, not be pulled drum-tight. EN 1263-2 limits fall height to 6 m (3 m within 2 m of the edge) and requires anchorages of 6 kN, spaced under 2.5 m — the installation guide covers this in full.
- Minimum sizes. A System S net under EN 1263-2 must be at least 35 m², with its shortest side at least 5 m. A net smaller than that cannot be a compliant System S net, however well it is made.
- Overlap and joins. Large areas are covered by joining panels. Say how panels should join — laced, clipped or overlapped — and how much overlap you need, so there is no gap a falling object can find.
- A sketch or photo. A dimensioned sketch, even a hand-drawn one, and a photo of the opening with the fixing points marked, prevent more errors than any paragraph of text. Measure twice, in daylight, with two people if the span is long.
Do not order a net exactly the size of the opening. A safety net needs slack to work: it catches by deforming, and a net pulled flat has nowhere to deform to. Tell the supplier the opening size and the fixing layout, and ask them to confirm the finished net size and the sag they have allowed for.
3. Mesh: the size that decides what gets caught
Mesh size is the opening in the netting, and it is chosen by what must not pass through:
- 100 mm mesh is the standard for a System S fall-arrest net under EN 1263-1. It is sized to catch a person, not a screwdriver.
- 60 mm mesh is used where smaller objects must also be stopped, or where a finer catch is specified.
- Fine debris mesh / debris liners are an additional fine layer for dust, small rubble and fixings. They are usually added as a liner to a fall-arrest net rather than replacing it — the combined-systems guide explains how the two layers work together.
- Under OSHA, mesh openings must not exceed 36 square inches (230 cm²), and no side of the opening may exceed 6 inches (152 mm).
Do not pick mesh by looks. A finer mesh catches more, but it also catches more wind, weighs more, and costs more to make and to handle. State what the net must stop — a person, tools, rubble, dust — and let the mesh follow from that. The mesh-size guide compares 60 mm, 100 mm and fine debris mesh in detail.
4. Material: the yarn behind the mesh
The material decides how the net behaves in sun, heat, chemicals and flame:
- Polypropylene (PP) is the commonest safety-net fibre — light and resistant to many chemicals, but the most vulnerable to UV unless stabilised.
- Polyamide (nylon) is strong and elastic, but unprotected nylon turns brittle in strong sun and must be stabilised for outdoor use.
- HDPE degrades more slowly in UV than PP, and is used where outdoor life matters most.
- Flame-retardant versions are available where hot work, welding or fire regulations require them, tested to EN 13501-1 or NFPA 701.
None of this is a reason to pick a material by reputation. Ask what stabiliser package is in the yarn — carbon black content, HALS, UV absorbers — and what test backs it. The materials guide compares PP, PET, HDPE and nylon; the UV guide explains why no safety net has a fixed service life in years, and why the annual test mesh is the only clock that counts.
5. Border rope, edge and fixings: where nets actually fail
Nets rarely fail in the middle of the mesh. They fail at the edge, at the rope, or at the fixing — which is why the edge specification matters as much as the net itself:
- Border rope. Under EN 1263-1 the border rope of a System S net must be at least 30 kN; under OSHA it must be at least 5,000 lb (22.2 kN). State the required strength in the order, and ask the supplier to confirm it on the label — do not accept "strong rope" as a specification.
- Edge reinforcement. Ask how the edge is finished: a reinforced border, eyelets or loops at what spacing, and tie ropes or lashings supplied with the net or separately.
- Panel connections. Under OSHA, connections between panels must be as strong as the net's integral components, and spaced no more than 6 inches (152 mm) apart. Say how your panels will join, and confirm the connection strength matches.
- Fixings. Anchorages, brackets and gallows are part of the system, not an afterthought. Confirm who supplies them — you or the net supplier — and that they meet the loads in EN 1263-2 or OSHA for your fall height.
If the quote does not mention the border rope, the edge finish and the fixings, it is not a complete quote. Ask for them to be itemised.
6. Label, test mesh and paperwork: what must arrive with the net
A custom net without its paperwork is an unidentifiable net, and an unidentifiable net cannot be tested, inspected or defended. Every net should arrive with:
- An EN 1263-1 label (or the equivalent for the standard it is made to): manufacturer, year and month of manufacture, class, mesh size, system, and the identity number that matches its test meshes. The label guide explains how to read every field.
- At least one test mesh — a piece of the same netting, from the same production run, loosely threaded through the net and sealed with the same identity number. It is removed and tested at intervals of no more than 12 months, to ISO 1806. A new net is normally supplied with three.
- A test report or certificate for the net's class, and the manufacturer's stated minimum energy absorption capacity that the annual test must meet.
Keep the label, the test meshes and the test history with the net for its whole life. A net whose test meshes have been cut off cannot be tested, and a net whose identity is lost cannot be traced to its test history.
7. What affects the cost — and what it does not include
No honest supplier can quote a custom net from a one-line request, because the price follows the specification. The main cost drivers are:
- Area and shape. Larger nets cost more, and an irregular shape costs more per square metre than a rectangle, because cutting and edging take longer and waste more material.
- Mesh density. Finer mesh means more yarn per square metre, more weight, and more handling — and a debris liner on top of a fall-arrest net is a second net, not a free addition.
- Material and yarn. Heavier twine, higher-tenacity yarn, UV stabilisers and flame-retardant treatment all add cost — and all of them are things a cheaper net may quietly leave out.
- Border rope and edge work. A 30 kN border rope, reinforced edges, eyelets and tie ropes are real material and real labour.
- Quantity. One net and one hundred nets are priced differently. Say how many you need, and whether repeat orders will follow.
- Testing and certification. Class testing, test meshes and documentation are part of the product, not an optional extra.
- Packing and shipping. Nets are bulky. Say where the nets are going, how they should be packed, and whether you need them folded, rolled or palletised.
What a quote should never do is hide these items in a single number. Ask for an itemised quote against your specification sheet, and compare quotes on the same specification — a cheaper quote for a thinner net is not a cheaper net. This article quotes no prices, minimum order quantities or lead times: those depend on the specification, the quantity and the factory schedule, and any supplier who quotes them without seeing your specification is guessing.
8. The specification sheet to send
Copy this list into your enquiry. A supplier who can answer all of it can make your net; a supplier who cannot is telling you something:
- Job: fall-arrest, debris containment, or both — and the standard (EN 1263, OSHA, ANSI A10.11).
- System (S / T / U / V) and class (A1 / A2 / B1 / B2).
- Opening dimensions (largest measurement per side) + fixing-point layout + sketch or photo.
- Mesh size (100 mm / 60 mm / fine debris liner).
- Material (PP / PET / HDPE / nylon) + UV stabiliser package + flame retardancy if required.
- Border rope strength + edge finish + eyelet/tie-rope spacing.
- Panel joins: how panels connect, and overlap required.
- Test meshes: how many, and the manufacturer's minimum energy absorption capacity.
- Label, test report and certificate required with delivery.
- Quantity, packing, destination and required delivery date — for the supplier to quote against, not for this article to promise.
Send that, and the net that arrives will be the net you ordered. Send a one-line request for "a safety net, about this big", and what arrives will be somebody's guess at what you meant — and the cost of finding out it was the wrong guess is paid on site, at height, when the net does not fit.
