Industry Insights & Guides

OSHA 1926.502 Safety Net Checklist: Mesh, Rope & Drop Test

OSHA 1926.502 safety net checklist: mesh size, border rope, drop test, inspection and clearance — the US construction safety net rules, in one checklist.

Construction worker in a fall-arrest harness working at height on a timber frame
OSHA 29 CFR 1926.502 sets the rules for safety nets on United States construction sites. It is not a long standard, but it is a specific one: it fixes the mesh size, the strength of the border rope, the distance below the work level, how far the net must extend, how it is tested, how often it must be checked, and how much clear space must be left under it. That is why the nine points below are the whole checklist, not a selection. The summary at the top is only the orientation; the checklist is the work that goes with it.
The Checklist
  1. Mesh size — openings no larger than 36 square inches OSHA limits mesh openings to 36 square inches (230 square centimetres), measured centre to centre of mesh ropes. The openings must be small enough that a worker cannot pass through them — and, once a load is applied, the mesh must not open up enough to let a body pass through.
  1. Border rope — minimum 5,000 lb breaking strength The border rope carries the load around the edge of the net. It must have a minimum breaking strength of 5,000 pounds (22.2 kN) at the time of installation. A connection, a shackle or a thimble that is weaker than the border rope is the weak point in the system.
  1. Distance below the work level — as close as practicable, never more than 30 feet Install the net as close as practicable to the working surface, and never more than 30 feet (9.1 m) below it. The point is that the falling distance should be as short as can be arranged — the further the worker falls, the harder the net has to work.
  1. How far the net extends — 8, 10 or 13 feet beyond the edge The net must extend outward beyond the edge of the working surface. How far depends on the vertical distance between the working surface and the net: up to 5 feet = 8 feet out; 5 to 10 feet = 10 feet out; more than 10 feet = 13 feet out.
  1. Drop test — 400 lb bag, tested on installation and every 6 months Before first use, after any relocation and at least every six months, the net must be drop-tested with a 400 lb (180 kg) bag of sand, 30 inches (76 cm) in diameter, dropped into the net from the highest working surface, or from the edge of the work platform where the net is used. A net which is damaged after a drop test — or after a fall — is not to be put back into service.
  1. Weekly inspection — look for wear, damage and deterioration Inspect the net at least once a week for wear, damage and deterioration. It is an inspection to catch a problem before the net is used, not an inspection to record that the net has failed. Damaged or worn nets must be replaced or repaired before the work restarts.
  1. Clearance below the net — nothing to hit on the way down The net must be installed with enough clearance below it that a worker who falls into the net does not strike another surface. What counts as enough clearance depends on the height of the fall and how far the net will stretch, but the standard expects the net to stop the worker and hold him, not let him hit the deck below.
  1. Connections and anchorage — full strength at every joint Connections between net panels must develop the full strength of the net. The net is only as strong as its weakest joint — and where the net is suspended by ropes or cables, the connections must be as strong as the net.
  1. Keep the net clear — debris and tools do not belong in it Remove debris, tools and materials from the net. The net is designed to catch a person — not to be a storage area for the site.
Common mistakes to avoid • A net that is installed too far below the working surface, so the fall covers a greater distance than it should. • A net with a hole small enough to pass a hand through, but too large to catch a person. • A net that has not been drop-tested after it was moved. • A net that has been used to store material on the deck — the practice is banned in the US standard.
A note on standards OSHA 1926.502 is US law for construction work. Outside the United States, EN 1263-1 is the common European standard, and its class and system structure is a different way of expressing the same idea: the net must be tested for a known drop, and installed as a system with its connections, anchorage points and guardrails. The requirements are the same in principle: fall arrest nets are designed to catch a falling person, and a net used for debris control is not a fall-arrest system.